Crown Trade Matt Vinyl Emulsion

Surfaces to be painted must be sound, clean, dry and free from dirt, dust, grease and anything that could affect adhesion.

Please note: Take special precautions when preparing pre-1960s painted surfaces, as they may contain harmful lead. Avoid inhaling dust during preparation and wear suitable respiratory protection.

1. Allow new plaster to dry thoroughly before decorating.
2. Remove loose material and any failing paint, feathering the edges of the remaining sound coating.
3. Treat mould, algae and other organic growth with a suitable fungicidal wash, such as Sandtex Fungicidal Wash. Follow the manufacturer's instructions and remove the growth.
4. Wash previously painted surfaces with warm water and liquid detergent, changing the water regularly. Wet abrade glossy or eggshell finishes to provide a key, rinse away all residues and allow to dry.
5. Fill holes, cracks and shallow defects with Prestonett Ready Mixed Multi-Surface Repair Filler. Once dry, smooth the repairs and remove all dust.
6. Prime any areas that remain powdery with Sandtex Trade Quick Drying Stabilising Solution, following the manufacturer's instructions.
7. Prime polished or dense surfaces with a suitable adhesion primer, such as Zinsser Bulls Eye 1-2-3 Plus, following its preparation and overcoating instructions.
8. Where stains remain after cleaning that could bleed through the finish, spot prime with a suitable stain-blocking primer. Allow to dry as directed before painting.
9. Mist coat bare porous surfaces and filled areas with Crown Trade Matt Vinyl Emulsion diluted with 400ml of clean water per litre of paint. Touch in any later repairs with the same primer or mist coat and allow to dry.

Always produce a test area to check suitability, colour and the final finish. Follow the manufacturer's instructions on the tin.

Air and surface temperatures must remain at or above 8°C, with relative humidity no higher than 80%, during application and drying. Ensure adequate ventilation throughout.

1. Stir thoroughly before and during use. When using more than one pack of the same colour, intermix them for colour consistency.
2. Apply with a good quality synthetic brush or medium pile roller. For airless spraying, follow the equipment manufacturer's guidance on dilution and settings.
3. Apply two full finishing coats over the prepared surface. Some colours may require additional coats for complete coverage.
4. Allow at least 4 hours between coats at 20°C and 65% relative humidity. The paint is touch dry in 1-2 hours under these conditions; colder or more humid conditions will extend drying times.
5. Clean tools and equipment with clean water or warm soapy water immediately after use.

Cleaning

Where cleaning is necessary, gently wipe with a soft cloth dampened with a mild detergent solution. Avoid scrubbing or vigorous rubbing, as this can leave shiny patches or remove the coating.

Maintenance

When redecoration is needed, clean and prepare the surface before applying further coats of Crown Trade Matt Vinyl Emulsion, following the Preparation and Application instructions above.

Yes, once the plaster is thoroughly dry. Apply a mist coat diluted with 400ml of clean water per litre of paint before applying two full finishing coats.

Yes, provided the existing paint is sound and firmly adhered. Clean the surface, remove failing paint and wet abrade glossy or eggshell finishes to provide a key. Bare areas and stains may need separate priming.

It can be gently wiped with a damp detergent cloth, but scrubbing can leave shiny patches or remove the coating. For surfaces that need frequent cleaning, consider Crown Trade Clean Extreme Stain Resistant Scrubbable Matt.

It can be used on suitably prepared interior walls and ceilings, but it is not a specialist mould-inhibiting or scrubbable finish. For areas affected by condensation and mould, consider Crown Trade Clean Extreme Mould Inhibiting Scrubbable Matt and address the underlying moisture problem.

Coverage is up to 17 square metres per litre per coat on smooth surfaces. A 5-litre tin can therefore cover up to 42.5 square metres with two coats, excluding any mist coat. Rough or absorbent surfaces will require more paint.

Apply two full finishing coats over the prepared surface. Some colours or colour changes may need additional coats for complete coverage. A mist coat on bare porous surfaces is additional to the finishing coats.

At 20°C and 65% relative humidity, it is touch dry in 1-2 hours and recoatable after 4 hours. Allow longer in colder or more humid conditions and ensure adequate ventilation.

Yes, it can be applied by airless spray. Follow the spray equipment manufacturer's guidance on dilution and settings, and use the protective equipment specified in the paint's safety data sheet.