Projects (A-Z)
Brands (A-Z)
Removes old layers of Bona Polish and Bona Freshen Up from varnished wooden floors.
Features
- A concentrated, non-toxic floor polish remover for wooden floors
- Suitable for water-resistant floor surfaces, such as varnished wood, tiles, PVC and linoleum
- Effectively removes Bona Polish and Bona Freshen Up from varnished wood floors
- Effective and easy to use
- Low odour and solvent-free
Brand
Drying time
5 mins
Coverage
Up to 50 m2 per litre
No. of coats
1
Size
1L
MPN
Please Select Size/Option
GTIN
Please Select Size/Option
Overview
Overview
Back
Bona Polish Remover effectively removes Bona floor maintenance coatings from wooden floors that have become tired, worn and scuffed prior to re-finishing. Can also be used to remove stubborn shoe scuffs and marks from polished floors. Bona Polish Remover is compatible with the following products:
Bona Floor Maintenance Products
| Product | Use |
| Bona Polish | A ready-to-use polish for tired varnished wooden floors |
| Bona Freshen Up | A ready-to-use, water-based polyurethane maintenance coat to freshen up most finished and pre-finished wooden floors in both commercial and domestic areas |
Preparation
Preparation
Back
For best results, remove any loose dust, dirt and grit by dry sweeping, using a soft broom, mop or vacuum cleaner prior to applying Bona Polish Remover.
Application
Application
Back
Always do a test area before starting any project to assess product suitability and final finish. Follow the manufacturer's instructions on the bottle at all times.
Dilution - 1 litre to 5 litres of water. For scuff marks: 1 cap / 100 ml of water.
- Apply the diluted polish remover to a section of the floor using a Bona Floor Mop or spray applicator
- Allow the solution approx. 5 minutes to dissolve the polish
- Scrub the wet section with a hard bristled brush or a scouring pad
- Wipe off the dissolved material with a mop and bucket of clean water
- Continue working section by section until the whole floor has been treated
- Replace the cleaning water frequently
- Once the polish has been removed, rinse the surface one more time using clean water
- It may be necessary to repeat this process several times depending on how thick the polish build up is
Please Note: The amount of water applied to the floor must be kept to a minimum so as not to cause any damage. Pay attention to large gaps in the floor and do not allow excessive amounts of cleaning solution to seep into open gaps. It is important that all traces of Bona Polish Remover are wiped up before applying a new layer of polish.
- For removal of scuff marks: Apply the diluted product to the scuff mark or the affected area
- After a few minutes scrub with a gentle non-abrasive scouring pad and wipe off any excess
Finishing
Finishing
Back
Once previous maintenance coatings have been completely removed, a fresh maintenance coat like ones seen in the Overview above can be applied.
Datasheets
Reviews
Reviews
Back
4 customer reviews
5.0/5.0
based on last 18+ months
5 stars
4
4 stars
0
3 stars
0
2 stars
0
1 star
0
Good quality
Recommended to us by floor expert and it is a good product that does the job properly.
Sarah Thomas. , 1L (27/03/15)
No complaints - works well
Excellent product to lift tough shoe marks on a community hall sports floor. You only us a little, so a litre lasts a long time since you also dilute it.
MARGARET EASTWOOD. , 1L (02/10/14)
Good
The polish remover did the job very well.
Maureen Davis. , 1L (10/06/13)
Softens bona freshen up to enable removal
Even with this hard work by hand :- Had new factory finished wood flooring put down 10 months ago, fitter said protect & seal with freshen up, I did, instructions said I could put more than 1 coat, I went overboard and did 3. OK until the grandchildren stayed for 4 months over summer, (2 & 4 yr old) plastic toys, buses cars etc. took a heavy toll, areas of the freshen up came off and other stayed, we are going back to original finish, and will use something which is easier to remove.
GERALD WRIGHT. , 1L (22/11/12)