Sikkens Rubbol BL Satura

  4.7/5.0 (13 reviews)
...
...
2 coats = Standard Protection
Total: enter area

Wood type and application method can vary coverage.

  • A high quality waterborne for interior and exterior timber
  • For wooden frames, doors and other timber surfaces
  • A good strong finish
  • Very good abrasion resistance
  • Excellent leveling and fast drying
  • Offers a opaque satin gloss non-yellowing finish
  • Low V.O.C content
Brand Sikkens
No. of coats 2
Coverage Up to 10 per litre
Drying time hrs
Size 1L, 2.5L
MPN 5006146, 5006147
GTIN 8711115165448, 8711115165462

Sikkens Rubbol BL Satura is used as a mid-coat for wooden window frames, doors and other wooden structure. Can also be applied to cleaned and sanded alkyd paint surfaces, for indoor use. For outdoor applications always in conjunction with a waterborne primer.

Moisture content of the timber should not exceed 18% prior to coating.

Bare or New Timber

  • Degrease any exposed bare timber surface by wiping with a cloth dampened in a suitable solvent
  • Resinous deposits should be removed with a scraper and any remaining residues should be removed using a lint-free cloth dampened with a suitable solvent
  • Allow solvent to evaporate fully before over coating
  • The use of knotting agents is not recommended as they are not always fully effective in 'sealing in' resin, and adhesion of coatings can be impaired
  • If using a wood filler, ensure that it is one that is specifically designed for use with timber, as general or all purpose fillers may not be suitable
  • Only use non-ferrous screws, nails and fixings

Previously Coated Timber

  • Base stained joinery should be denibbed using a fine grade nylon abrasive pad or a fine grade (P240 or finer) wet or dry silicon carbide abrasive paper, in the direction of the grain, ensuring not to break through the surface coating
  • Remove any remaining sanding dust
  • To ensure optimum durability and uniformity of appearance, Sikkens recommend a coat of Sikkens Cetol HLS Plus prior to finishing
  • Where necessary, stop with tinted putty
  • Where there is localised damage, or deterioration has occurred as a result of exposure of the factory coating for longer than 3 months, affected areas should be thoroughly sanded back to a sound substrate

Old Timber

Decayed timber must be removed and replaced, cutting at least 25mm into sound timber.

.

We always recommended applying a test area to ascertain drying times and effect. Sikkens is ready-to-use from the tin, do not thin.

New or bare wood

  1. Before application of Rubbol BL Satura, add a primer such as Sikkens Rubbol BL Primer for extra protection against the wood using a soft brush or roller
  2. Fill in joints and defects with a relevant filler
  3. Sand down surface
  4. Make sure all dust is gone
  5. Immediately apply a coat of Rubbol BL Satura
  6. Let dry for 6 hours
  7. Sand down lightly and reapply another coat as above

For further information relating to this product and its application, refer to the relevant product data sheet from Sikkens.

Regular Cleaning

If needed, wipe over with warm water to clean and dust.

Repair

Lightly sand with a fine grade abrasive paper to keep splinters and rough edges away.

If the timber has been stained, lightly sand but avoid sanding back to underlying stain. Remove all dust thoroughly and apply 1 or 2 coats of Rubbol BL Satura.

13 customer reviews
4.7/5.0
 
Easy to work with by Graham Marshall

Leaves a very good finish after 2 coats,

Reviewed 2.5L on: 13/12/16
Great finish by Richard

Great finish and easy to use

Reviewed 2.5L on: 09/11/16
Best of its kind on the market Excellent results by Joe Mansberger

The technical data sheets provided are very useful. I followed the suggested application exactly and the result was always perfect and to a very high professional standard.

Reviewed 2.5L on: 26/10/16
Seem good, would prefer less gloss by George Delandro

good cover, spreads well. surface dry a bit to quickly, so there is a risk of "dragging" marks.

Reviewed 1L on: 20/09/16
A great product and the best price from Wood Finishes by Gary Chattenton
Reviewed 2.5L on: 05/09/16
Excellent product, as expected the perfect partner to the undercoat by Andrew Farmer

Easy to use (can be a bit messy) as it flows well, and provides an excellent topcoat for the primer/undercoat that I am using (Sikkens Rubbol BL Primer ). Ensure that the preparation instructions are closely followed, and a hardwearing finish will result. I have used the product before, but this is the first time I have used it with the primer, very pleased with the result.

Reviewed 2.5L on: 18/08/16
Nice finish and easy to work with by Kevin Hughes

Used this over Zinsser to paint varnished skirting and it leaves a nice smooth finish with a lustre. Dries quickly and very little smell.

Reviewed 1L on: 21/07/16
Good by Tessa Lash

does need a good undercoat/primer and does chip easily but otherwise good as very low voc

Reviewed 2.5L on: 12/07/16
Fantastic finish and easy to apply by D.Williams

I was very pleased with this product and look forward to the paint keeping its whiteness.

Reviewed 2.5L on: 08/07/16
Amazing water based satin finish by Kris Bennett

Used to paint skirting boards and stairs. Easy to apply, easy to wash brushes, great finish and no yellowing like gloss.

Reviewed 2.5L on: 10/04/16
Not really used it yet by M Ray

Was recommended by the site manager for the new house we have purchased. He said that this is the paint that has been used throughout the house.

Reviewed 1L on: 13/03/16
Excellent by Steve Cook

Great product and very prompt service and delivery thank you will buy from here again

Reviewed 2.5L on: 29/01/16
Excellent product by NINA

Great finish,it dries very fast.

Reviewed 1L on: 05/11/15

Customers also bought

Ask a question Live Chat