Blanchon Hard Wax Oil Tints

Blanchon Hard Waxoil Tints is a coloured hard wax oil for wooden flooring, skirting boards, worktops, furniture and any other interior solid wood, plywood and cork. It penetrates into the surface to provide long-lasting protection.

• Looking for a clear, natural look instead? Try Blanchon Hard Wax Oil

Ensure that surfaces to be treated are clean, dry and free from any dust, dirt or other surface contaminants. In general, there should be less than 10% moisture content.

Old Timber

1. Sand old wood flooring back to bare wood with 24 or 36 grit paper, then with a 50 or 60 grit and finish with a 100 to 120 grit
2. Then treat as new timber

New Timber

1. Sand back new or bare wood with 120 grit paper
2. Carefully vacuum the area to remove all traces of sanding dust
3. Any oil or resin that exudes from exotic woods should be removed with methylated spirit

Always do a test area before starting any project to assess product suitability and final finish. Follow the manufacturer's instructions on the container at all times. Blanchon Hard Waxoil is ready to use and does not require diluting or mixing. Shake well before use.

Do not apply to wood if the temperature is lower than 12&degC; or if the relative humidity is higher than 85%. Never use on wood where the moisture content is higher than 10%. Use only in well ventilated areas. Keep any aquariums and plants away from the environment where the product is being applied.

1. Apply the Hard Wax Oil thinly with a natural bristle brush or short-haired roller, in the direction of the wood grain
2. Wipe very regularly as you apply with a clean, lint-free cotton cloth (in a circular movement), a buffing machine fitted with a soft beige or white pad, or a polishing machine fitted with soft brushes
3. To make buffing easier, only work on one small area at a time
4. Allow 8 - 12 hours drying time before applying the second coat in the same way as the first

The finished area can be subjected to light use 8 -12 hours after the final coat and fully utilised 2 - 4 days after applying the final coat. It takes 8 to 10 days to fully cure. However, the following precautions should be taken in the first few days of use:

• Do not cover (use protective sheets) or lay rugs onto the area
• Remove dust with a vacuum cleaner, brush or cloth (do not use impregnated fabrics)
• Do not move heavy furniture around
• Immediately wipe up any water or other liquid spillages and take particular care with flower pots
• Subsequently, appropriate protective measures (i.e. felt pads) should be taken for table and chair legs or other objects which could mark the floor
• If applicable, a quality doormat at the entrance will be of benefit
• A wood floor needs the right environment and a room temperature of 19 - 21&degC; and 50% - 65% relative air humidity are ideal

Regular Cleaning

Remove dust regularly using a microfibre mop or vacuum cleaner. Stains and marks can be easily removed with a dedicated floor cleaner and a damp floor mop or cloth. Never soak wooden floors with water.

Deep Cleaning

1. Wipe wood floors with a damp mop or lint-free cloth using diluted Blanchon Natural Soap or Blanchon Lagoon Cleaner, for frequent cleaning
2. Work on one area at a time, rinsing the microfibre mop or cloth regularly. It should always be well wrung out to avoid getting the wood floor too wet

This should be carried out from once a week on light traffic floors or more frequently for heavy traffic areas.

Maintenance

Maintenance should be carried out when the Hard Wax Oil finish begins to look tired or worn. On high traffic wood floors, regular maintenance may be boosted by applying a thin coat of Blanchon Maintenance Oil or Blanchon Universal Maintenance Oil and buffed if required, either by hand or with a floor buffing machine.

Allow 15 days before the first maintenance treatment to allow Blanchon Hard Wax Oil Tints to fully cure. The polished area should be fully use-able in 4 - 8 hours.

Repair

For small areas with specific damage (cigarette burns, impact damage etc.) lightly sand with 120 grit sandpaper to remove the damage and then re-apply Blanchon Hard Wax Oil.

For larger areas or wood floors that have not been maintained as frequently as their use requires, a general sanding can be done using a buffing machine fitted with a sanding disc (about 120 grit) before applying a coat of undiluted Hard Waxoil. Polish by hand or with a buffing machine.