Sadolin Extra Durable Clearcoat

Sadolin Extra Durable Clearcoat is perfect for a wide range of exterior wood projects including windows, doors, conservatories and more. It is ideal for over-coating Sadolin Classic Wood Protection and Sadolin Extra Durable Woodstain.

Please Note: This product is not suitable for high traffic areas such as flooring and decking. For decking, see Sadolin Decking Oil.

• Looking for an alternative clear coating for exterior wood? Try Sadolin Outdoor Varnish or Sadolin Yacht Varnish

Ensure all timber surfaces to be treated are fully clean, sound and dry. The moisture content of the timber should not exceed 18% prior to coating.

Bare Timber

• All traces of surface dirt and debris, including mould, algae and fungi, must be removed prior to application with a scraper, stiff brush or broom
• Areas affected by biological growth should be treated with a suitable mould and mildew cleaner.
• Resinous deposits should be removed with a scraper
• Always degrease any exposed bare timber surface by wiping with a soft, lint-free cloth dampened with methylated spirits
• Any defects in the wood should be filled with an appropriate wood filler
• Only use non-ferrous screws, nails and fixings

New Timber

• Pre-treat new timber with a suitable preservative , such as Sadolin Quick Drying Wood Preserver, for best protection
• Where possible, the wood preservative and Clearcoat should be applied to all parts of the wood prior to fixing in place

Previously Coated Wood

• Where there is localised damage, or deterioration has occurred as a result of exposure of the factory coating for longer than 3 months, affected areas should be thoroughly sanded back to a sound substrate and re-coated
• Previously coated wood in good condition should only require a light sanding to aid with adhesion
• Wash down with warm water and detergent, allowing to dry before application of Sadolin Clearcoat
• For surfaces in poor condition, remove any loose, flaking material and any grey, weathered timber by thoroughly sanding in the direction of the wood grain
• Do not break through the surface coating
• Ensure that all surface dust and debris from sanding is removed before coating with Extra Durable Clearcoat

Base Stained Joinery

• If bare, joinery should be patch primed with one or more coats of Sadolin Classic Wood Protection in the appropriate colour to match the existing base stain

Glazing

• The backs of new glazing beads, end grains and rebates should be brought to a finish with the full Sadolin Extra Durable Clearcoat system prior to fixing
• The use of linseed oil putty or modified, non-setting compounds are not recommended in conjunction with Sadolin wood protection systems
• To confirm compatibility, please consult the manufacturer of the relevant glazing material
• Silicone glazing materials should only be applied upon completion of the finishing coats

Always do a test area before starting any project to assess product suitability and final finish. Follow the manufacturer's instructions on the tin at all times.

Do not apply Sadolin Clearcoat if there is a risk of rain, or when air / substrate temperatures are below 8° or above 25° or if the relative humidity is above 80% during application or drying periods. Protect from frost and rain until dry. Failure to meet these requirements may adversely affect the drying, visual quality and durability of the finish.

1. Ensure clear coat is thoroughly stirred before and during application
2. Apply Sadolin Extra Durable Clearcoat with a good quality, natural bristle brush
3. Apply in a full flowing coat, ensuring all surfaces and end grains are fully coated
4. Pay special attention to end grain, tops and bottoms of doors, and undersides of sills
5. Allow a minimum of 16-24 hours drying between coats
6. Apply second coat as above
7. If applying this product on its own without a base coat, 3 full coats are advised

Please Note: The amount you need may vary depending on surface condition, moisture content, method of application and climatic conditions during application.

Regular Cleaning

For regular cleaning, wooden surfaces can be wiped down with a dampened, lint-free cloth and warm, soapy water.

Maintenance

The need for maintenance is indicated by a lightening in colour, reduction in sheen as the coating erodes, and a loss of water repellent qualities.

When the layer of finish is getting thin, simply wash down with warm, soapy water (mild detergent) and re-coat with 1 or 2 coats of Sadolin Extra Durable Clearcoat.

Repair

1. When removing organic growths, or greying in the wood, treat with a suitable fungicidal solution and lightly sand the surface
2. Patch prime the areas where sanded with Sadolin Quick Drying Wood Preserver
3. After, simply add 1 or more coats of Sadolin Classic Wood Protection or Sadolin Extra Durable Woodstain in the appropriate shade to match existing colour
4. Then overcoat with Sadolin Extra Durable Clearcoat

If the finish is badly flaking or peeling, to the point where the bare wood is showing through or has started to grey, lightly sand and follow the full Preparation and Application instructions above.

Can Sadolin Extra Durable Clearcoat be used on decking?

Sadolin recommend that Extra Durable Clearcoat is not used on decking due to its high surface build and shiny finish. This product is likely to wear quicker than a dedicated decking stain or oil and could pose a slip hazard.